Quantcast








     

Turbo Ace 908 Motor mounting screws

helifreak.com - 2013-05-18 00:11:27 - Similar - Report/Block

So my stock motor is getting pretty tired, and this Turbo Ace guy is $29 , so why not... Unfortunately the stock motor screws are too big for this motor. Does anything else have this motor? How did you mount it? Saw one thread w/mention of mCPX motor screws fitting. Can't find what dimensions those are to order them...

Mounting screw for HP08S came off

helifreak.com - 2013-02-12 03:12:38 - Similar - Report/Block

I used the carbon motor mount stiffener & screws with washers to fix the motor to the frame. One of the screws came off during spool up. Should I use CA or loctite to secure the set up? If yes, it should be applied to between the washer/stiffener or screw/motor?...

Looking for good replacement main motor

helifreak.com - 2013-05-21 06:29:39 - Similar - Report/Block

Ok I'm looking for a good replacement motor, I don't want to go brushless, for that ill buy a mcpx bl and save time and money. Does anyone know the dimensions of the stock brushed motor, length, max voltage, rpm etc... Also has anyone experimented with using a different motor maybe from a t-Rex 100 or a heli-max 100. I know the diameter o...

Spin 8000 motor deal.

helifreak.com - 2013-03-01 06:42:10 - Similar - Report/Block

Mark, at Tmkarc has the spin motor for 29.99 right now. This is the same batch that came with the wrong screws in the package that i got from him. If you have a spin motor already you should have two extra screws that will fit this can. And if you know where to find screws this small with the right thread this is a good deal. http://tmkar...

TREX 500 PRO DFC motor doesn't fit mount holes

helifreak.com - 2013-04-24 19:18:57 - Similar - Report/Block

Part way through my first build. Tried to install the motor but the mount holes in the motor mount are way too wide for the motor holes. It seems odd. Has anyone any suggestions? In he attached photo you can see that I have screwed the screws into the motor and just doing a visual you can se that they are ny aligned to any holes in the mo...

Wicked motor with stock pinion?

helifreak.com - 2013-06-11 15:34:00 - Similar - Report/Block

Will the stock 9T pinion work on the wicked 4800kv motor? Ordered a motor directly from don's site and was hoping to just use my stock pinion for the moment. The shaft on the stock motor is thicker at the base as is the diameter or the stock pinion. So when I slide the stock pinion on the wicked motor at the bottom where the set screw goe...

WTB: Need a VF43 Turbo, New block and cracked exhaust housing!

iwsti.com - 2013-02-05 06:16:24 - Similar - Report/Block

As the title says, i'm looking to purchased a turbo to put on my 2007 sti. I am recently getting a built block put in and am planning on going big turbo in the future. While the motor was out, i inspected the turbo and noticed there was a pretty decent crack on the exhaust housing. I am not sure if its fine to run with the crack as i read...

Spin motor holes not tapped.

helifreak.com - 2013-02-22 07:43:11 - Similar - Report/Block

Just got my new spin motor today and the motor holes were not tap the right way. The screws wouldn't even go in any of the 4 holes on the can.:face I have seen on here where other ppl are having the same thing happing to them also. This really sucks because tmkarc is out of stock now. I hope Xtreme will send me a new one to make up for th...

MSH Protos 500 - Airframe

helifreak.com - 2013-03-20 15:13:29 - Similar - Report/Block

Please note that this is a revised thread from my original posting. The motor and servos were purchased so this is what I have left. - protos 500 plastic airframe - SAB 425mm main blades - MSH FBL upgrade kit - Stock canopy - MSH orange skids - MSH orange tail blades The kit will come with the above and all of the stock kit pieces and par...

Which Scorpion motor and stock ESC

helifreak.com - 2013-02-25 20:02:57 - Similar - Report/Block

I've been running a Scorpion 2208-4660 and its been ok. Quieter than the stock motor and no vibrations with a little more power. Well I bent the shaft and looking for a little more motor that I can still use the stock ESN. Talked to Innv8tive Designs and they said the next 2 sizes up would be good for sport flying but for 3D the ESC may n...

2 BLADE 130X $400 SHIPPED

helifreak.com - 2013-06-09 03:14:48 - Similar - Report/Block

2 blade 130x forsale $400.00 shipped first one is all stock needs board second one is complete mircoheli needs servos and board with lynx dfc and extreme metal gears a b c and d and turbo ace 908 brushless motor 3 working ds35 servos was from for mh frame 6 450 mah lipos one extra microheli frame blades screws stuff like that will include...

Where to get motor screws?

helifreak.com - 2013-03-24 01:07:40 - Similar - Report/Block

Took my Warp out today for 12 trouble free and awesome flights (just finished setting up governer and Scorpion 2520 10 pole torque monster) and had a few minutes of daylight left so I decided to dust off the ol' 1turdyX which I shelved awaiting new Lynx DFC and replacement Spin 8K motor shaft. It still has the wobbles which I can't figure...

evolveStar Join

best quality cap head screws

helifreak.com - 2013-05-08 06:38:44 - Similar - Report/Block

hello everyone! im looking for some high quality m4x10mm socket head cap screws. im putting bigger blades on my trex 600 12s that will be ran at high headspeeds and plenty of pitch and i want to make sure the blades dont fly off from the extra stress. does anyone know of some screws that will have higher strength than the stock aligns? im...

AL SR20 OEM T25 Turbo

zilvia.net - 2013-04-18 16:09:08 - Similar - Report/Block

I have a stock t25 turbo from an SR20. It has a normal shaft play. Turbo did not produce any smoke. I am selling because I purchased another turbo for my car. This turbo ran fine with no issues. There are two broken studs on the hot side of the turbo. There is also a little bit of oil inside the turbo housing on the cold side. This was no...

HK Turnigy 2627-4200 Motor swap

helifreak.com - 2013-02-21 11:30:42 - Similar - Report/Block

Anyone changed the stock motor out for the turnigy 2627 - 4200kv motor? Im sick and tired of the vibes given off by the stock motor and the wicked has been out of stock every time ive had the cash :-( I have a turnigy motor in my hands right now that id like to swap out. Looking at the stocker i think they are what 4600kv? is there going...

FS: [NEW] Scorpion HKIII-4035-560KV Motor 600/700

helifreak.com - 2013-05-28 02:14:35 - Similar - Report/Block

This is a brand new motor out of my Logo 600SX combo kit. I decided to go with a different motor for the build. Never had screws in it, pinion, or plugged in to anything, 100% new! Sells for $250, $200 shipped. Specifications: Stator Diameter ............................ 40.0 mm (1.575 in) Stator Thickness ........................... 35.

Stock motor longevity

helifreak.com - 2012-09-16 07:08:58 - Similar - Report/Block

Had to retire my first (coreless) motor after 220 flights, mostly low key sport flying and a handful of unpowered crashes whilst coming to grips with my 1st CP heli. The motor started misbehaving at spoolup and cutting out intermittently midflight. I had visions of a $75 3 in 1, but a new motor fixed all problems for $12. So what sort of...

Thunder Tiger E325 Stock Motor and ESC

helifreak.com - 2013-05-31 03:10:34 - Similar - Report/Block

Asking $55.00 shipped. These have been used for about 100 flights on a stock Mini Titan. I have upgraded the heli and no longer need the stock power system. It is the OBL series motor for the e325v1 and the Ace BLC-40 ESC. Let me know if you have any questions! Attached Thumbnails...

Hobby King Brushless motor

helifreak.com - 2013-04-20 01:06:05 - Similar - Report/Block

This motor: http://hobbyking.com/hobbyking/store...s trSearch=2415 Brand new, never used. I will throw bullet connector for ESC and motor, If I find an pinion it will go for free also. I found the mount screws for this motor and Rhino 13T pinion $10.00...

Walkers master cp upgrade bl motor

helifreak.com - 2012-09-10 01:21:31 - Similar - Report/Block

Hi guys, anyone knows a upgrade brushless motor for walkera master cp yet? How to upgrade the stock brushed motor with that receiver unit? Seems one stock speed controls both main motor and tail...

Hpo6 2s 8200 kv motor in my 130x

helifreak.com - 2012-09-06 22:32:56 - Similar - Report/Block

Hello fellow helifreakers. I have another motor mod to show and tell about which is about the Hpo6 2s 8200kv motor. I find this motor good to run on a secondary 130x or for the guy that don't like cutting on their heli frames. This motor has plenty of power to pull off nice loops rolls invert flight good old fashion sports flying. As for...

Governor Mode ESC settings for 700E

helifreak.com - 2013-05-05 17:43:51 - Similar - Report/Block

Hey guys, Getting ready to set governor mode for Ice2 HV 80 for Trex 700E FBL V2. Stock 700mx motor. Questions: What is the motor and gearing information for the stock pinion, ESC? I know the motor is 530kv, not sure how much poles the motor has or the pinion ratio. I'm sure someone else has done this before and has this information. Paul...

Trying out the Turbo Ace 908 motor

helifreak.com - 2013-05-05 07:39:49 - Similar - Report/Block

Saw this newer motor from Turbo Ace for the 130X. They are on sale for $29 so I ordered one up. I figured it would just be a new version of the hp08 but it is larger in diameter and has a thicker shaft. The end is turned down to fit a standard pinion. I only got a few flights on it today and it is a very strong motor at 85%. It came with...

Outrage BL 9180 servo mounting Logo-500

helifreak.com - 2013-04-21 01:26:11 - Similar - Report/Block

These are the servos I selected. I test fit one in the slot. Tiny bit of sanding to remove flashing but seems to be nice drop-in & bolt pattern lines up perfect. - Is it advisable to use the included rubber dampener biscuits & metal eyelets across the mounting ears? (vs. hard mounting the servo to the frame?) - The screws are pretty hefty...

trex 550e 3gv1 ice100 spool up problems +more

helifreak.com - 2013-04-23 03:11:10 - Similar - Report/Block

Ok so I havent flown my 5503g v1 for about 6 months, because on the last flight appx 6 months ago, it would not spool up, the motor would just jerk a bit and that would be it. (using stock align 600 1220kv motor) I called castle and explained the problem, they told me it was probably the motor. Jump forward 6months i decided i wanted to f...

CA T28 s14 Turbo, SR20DET "WC" Ecu, 69F00 MAF...etc..

zilvia.net - 2013-03-23 10:08:24 - Similar - Report/Block

Hi, I have some parts laying around for sale....They are removed from an s14 Zenki SR20DET.....They are in great working condition.......I bought the whole motor for just the block to build my race engine...So, the rest need to be gone to fund my race motor 1. SR20DET t28 Turbo (P/N: 14411-69F00).....No shaft play..... +++Stock wastegate...

HP08S from RCepot?

helifreak.com - 2012-09-15 16:10:48 - Similar - Report/Block

Like some of you previous Blade owners, I swore I was going to try to keep this bugger stock, but I broke down and ordered a HP08S motor and pinion from RCDepot. I just paid for regular shipping. Are these guys in China? How long should it take to get here. I'm Ok with the stock motor, but, I'm using Zippy Compact 500s which make it a lit...

New Xera 4030/3Y-470 KV Motor For SOLD!!!!

helifreak.com - 2013-06-05 17:11:29 - Similar - Report/Block

I have a new and unused Xera 4030/3Y-470 KV motor for sale. It will come in it's original box and even has a receipt for warranty purposes. Once again it is NEW and they retail for $240. I just got this from another RR member in perfect condition and then realized I can't use it as it has 25mm bolt spacing. Powerful, efficient motor, perf...

SR20 Lean Condition

zilvia.net - 2013-03-18 17:16:09 - Similar - Report/Block

Recently got a sr20. Drove 8 hours home and was a strong motor. Did a compression test at time of sale and 150 across the board. Stock Motor, Stock Turbo, Stock pressure and vacuum. Recently I have been leaning out at idle and at cruise according to aem wideband. I can definitely feel it too. Bogs, pops. Under WOT my ratio is 11.3-12, dec...

Mini protos 6s setup questions

helifreak.com - 2013-05-05 02:22:44 - Similar - Report/Block

i am thinking about going 6s with my mini protos i haven't really flown it much .. i am going to buy IKON fbl system for it as i didn't have much luck with my beastx and that is know on my gaui nx4 which works flawless. but i have seen everyone talking about this motor from scorpion HK2520-1360 which i cannot find stock anywhere in the u.

DS35 as elevator servo

helifreak.com - 2013-02-26 14:52:53 - Similar - Report/Block

I got fed up of replacing burt out stock elevator servos so have mounted a DS35 alongside the stock motor on outside of battery holder plate, using existing linkage wire and just removing the middle plastic bar of the battery support platform so the servo arm can go through. 2 screws hold the servo snug, canopy fits and heli flies fine. T...

450 pro FBL w BeastX Excellent condition BNF

helifreak.com - 2012-11-15 07:37:26 - Similar - Report/Block

450 pro fbl excellent condition carbon tail boom Align 450M motor 410m's on cyclic 520 on tail. BeastX v3.08 Spektrum 6110 receiver Includes 2 Hyperion 45C 2200 mah lipos. Photos speak for themselves. Great flying heli. Stock Align motor has been rebalanced to reduce high frequency vibrations(stock balancing is horrible). The motor was ba...

Whiplash Gasser Motor Question

helifreak.com - 2013-05-14 05:01:15 - Similar - Report/Block

I currently have the whiplash 90E and really like it, so I was thinking about building the Whiplash Gasser but since I only fly scale like, maybe a roll or short inverted hover. Do I need to have a modified motor. Is a stock motor fine and is anyone on here running a stock motor? I know some of the modification is to smooth out engine vib...

KDE Universal Mount

helifreak.com - 2013-05-08 04:49:51 - Similar - Report/Block

Just got mine in the mail today. Does anyone have any experience with these mounts. I'm a little skeptic as to how they work...... I can see this ending in utter disaster. Those 4 screws are supposed to hold the mount on the rails? Can this be used with the stock Align 600MX motor? Thanks...

Best replacement for dead GCP V2 motor

helifreak.com - 2013-03-18 07:04:06 - Similar - Report/Block

Hello dear helifreaks : Yesterday my GCP V2 stock main motor just died...initially it barely lifted about 1 Mt off the ground, and later it diea. I was flying some circuits in quite some wind on the beach, and also some sand got into the swashplate and maybe motor too, so I have to check first. So, the big question is : what are the best...

Mikado/Scorpion 4525-520kv Ultimate with an 8mm shaft

helifreak.com - 2013-05-21 17:37:30 - Similar - Report/Block

I have a for sale. This motor is the stock motor for a Logo 700. I'm moving to 14s so I don't need this motor anymore. This motor is about 20 flights old. Asking $280 Shipped. That's about $100 off retail price!...

Newbie Build Question(s)

helifreak.com - 2013-05-08 04:08:10 - Similar - Report/Block

Hello all, I am the proud owner of what some day might be an Atom 500, if I can swing this learning curve! Please be patient as I muddle my way through this - my first - build. Also, to be frank, relatively new to the hobby in general. Anyway, I was just sort of looking things over to get the feel for what I needed to do, and I cannot see...

What TC matches stock running a Spin 8000kv

helifreak.com - 2013-03-20 23:26:12 - Similar - Report/Block

With a 11 tooth pinion ?. I noticed the Spin has way more power and RPMs vrs the stock motor. Id like to match R.P.Ms to start with and work my way up. So if I were to run the stock motor @100% Flat line TC what TC would match that with a spin ?? I did try 70% and even that seemed like it had more head speed.

Scorpion HKIII-4035-560 (Logo 600)

helifreak.com - 2012-10-23 05:29:04 - Similar - Report/Block

I purchased this motor with the intent of running it in a Logo 600 on 10s. I ended up going with a 12s motor instead. This motor has *never* been used. It does, however, have 5.5 mm bullet connectors soldered on to the leads. The stock scorpion motor bullets are included as well. This motor has not been used at all. Never. I'm asking $185...

BEC for 450 DFC with AR7200BX?

helifreak.com - 2012-09-17 05:08:57 - Similar - Report/Block

I just ordered a 450 DFC kit and will build it up with a Spektrum AR7200BX... Is this something the BEC in the stock Align ESC can handle? With a Sat Rx? Planning on using stock servos, stock motor, stock CF blades and stock tail.




dialogShowMessage!

Fill out the form you see below. Registration is free, fast and simple.
If you are already registered, sign in page login.


Web Site :
Required Field
First Name :
Required Field
Last Name :
Required Field
Email :
Required Field
Sex :
Required Field

evolveStar.com is free for ever !


evolveStar.com provides a search engine that allows you to gather information to write their own blog.


evolveStar.com enhances the sources displaying the logo of the site.


If you want to remove your site or you believe a site listed infringes copyright, please report it to: info@evolvestar.com


Specifies the subject copyright violation and the url of the page


evolveStar.com respecting the law DMCA (Digital Millennium Copyright Act) will immediately remove whatever its merits.


Next will be effectual and relevant checks.







Who We Are Partner Advertising Contacts Privacy terms Help & FAQ

© Copyright 2010-2017 Fabrizio Fichera. All rights reserved.