Quantcast








     

Servo voltage stabilizers | Stabilizer Supplier

bookmarklinking.com - 2013-04-19 08:24:23 - Similar - Report/Block

Servo Stabilizer Manufacturers - We are a coveted name in the market, trading, exporting and supplying a variegated range of products like Servo Voltage Stabilizers, Isolation Transformers, Stabilizer Supplier, Variable Auto Transformers, Constant Voltage Transformers and more.

Servo voltage question

helifreak.com - 2012-09-23 04:33:25 - Similar - Report/Block

Hi folks! I have a spare Futaba S9254 servo that I am thinking about putting on my Goblin 700 for the tail servo. I will be using a MSH Brain. Problem is the voltage of the S9254 is 4.8v. Can I power the cyclic servos with 6.0v and then use a step down to 5.1v regulator for the S9254? Could .3 volts still be harmful to the S9254? Thanks!...

Question about vbar, 2s power and servo draw

helifreak.com - 2012-09-14 09:07:15 - Similar - Report/Block

L bet this has been asked Berle, but I could not find the answer I think I'd like to go with a 2S flight pack. I have decided on the SAvox HV 2771 and 2772 servos, and I have two questions. This will be my first helinwith HV servos 1. Can the vbar full size run at 2s voltage? What about the satellites, or does vbar drop its voltage to pow...

Recommend EMI proof servo?

helifreak.com - 2013-05-10 07:55:21 - Similar - Report/Block

I don't have a helicopter question, its more general. I'm working with the Hitec HS-422 servo. It works fine until there is some EMI in the room from a high voltage coil I got. It starts bouncing around like a fish out of water. It's definitely the servo as I disconnected the controller and everything else and only applied 5V to it and it...

WTB BL750H High Voltage Brushless Servo*

helifreak.com - 2013-06-08 00:52:12 - Similar - Report/Block

Im looking for (2) BL750H High Voltage Brushless Servo* servo Pm with details :peace:quotes...

For Sale: New in Package Align BL700H / BL750H HV Servo Combo Package

helifreak.com - 2013-03-19 01:08:25 - Similar - Report/Block

***For Sale*** For Sale is a New In Package Set of (3) Align BL700H High Voltage Cyclic Servos, and (1) BL750H High Voltage Tail Servo, complete with all factory supplied hardware and servo arms and wheels. I had these sitting to use on an upcoming Rush 750 Build, but have decided to try out some MKS HV Servos. This package would normally...

servo choices???

helifreak.com - 2012-10-17 02:33:45 - Similar - Report/Block

Starting a new furion build ( 2 actually one 6s one 10s) and would like your opinions on servo choices. Futaba tail servo bls251 runs @ 4.8 while cyclic bls451 run @6 v . JR $$$ but flashy align cyclic 610 and tail servo (650) run @ 6 v no voltage regulation required. The aligns are compatable in torque with futaba but most economical so...

Scott Gray Reactor X2 Voltage Regulator $50 shipped anywhere

helifreak.com - 2013-03-25 08:41:51 - Similar - Report/Block

Used but good condition Scott Gray Reactor X2 Voltage Regulator. With this system you can run your whole system at 6v, 6.8v or max voltage; or you can run your cyclics at max voltage and the rest of your electronics including tail servo at 6 or 6.8v. I have been running DS610s at max voltage and tail DS650 at 6.8v. Comes with an XT60 conn...

Shutter Release Servo Trigger / Timer

helifreak.com - 2013-03-20 13:10:42 - Similar - Report/Block

Hi, Im looking for a device to activate a servo to give shutter release every second on My Panasonic LX3. I heard of shutterbug, but cant find a supplier. I can supply the device with 5V from my bec and then need it to send a signal to the servo to push the shutter button every second or so for the duration of the flight. I can arrange t...

MiniV voltage drops

helifreak.com - 2013-03-15 16:54:23 - Similar - Report/Block

Need help with my MiniV. I'm getting voltage drops when pitch pumping on the bench. Can I fix this with adding capacitors? If so, which capacitors do I use and where do add them? Setup is Align BL70G, DS515M cyclics, and Ds525m tail servo. 6S battery. To add, I get voltage drops even with a Castle BEC Pro and a Hercules HC BEC (5a cont.)...

MSH 80A ESC with 4a UBEC - and - DS 8910 servo

helifreak.com - 2013-03-15 14:26:23 - Similar - Report/Block

I cannot find anywhere the output voltage of the MSH 80A ESC with 4a UBEC. One would think it would be listed in the specs or in the instruction manual, or maybe even on the unit itself - but no. Closest I could find was for the YEP clone which has an output of 5.5 to 6v and is adjustable (they list their voltage specs... what a concept).

What Exactly does Variable Voltage Mode Mean? What are the ohms at each setting?

e-cigarette-forum.com - 2013-03-26 14:24:55 - Similar - Report/Block

I have two Joyetech ego 650's and a 1000 pass through that are Variable Voltage. I know how to turn on the variable voltage and such, but what exactly is happening when you opt for the second voltage option? What voltage are we talking about at each setting?...

evolveStar Join

What is the voltage drop when 1n4001 diode is added

helifreak.com - 2013-05-14 01:30:08 - Similar - Report/Block

I am posting this here because it seems a lot of people are putting in a diode for the tail servo for the 450x. I purchased the 1N4001 diode from Digikey and have soldered it to my adapter for my tail servo as a stepdown from 6v. I then plugged it in the beastx which has a cc bec running at 6v. When used the multimeter to check for volta...

From Jeti 2013 catalogue

helifreak.com - 2013-04-09 04:19:24 - Similar - Report/Block

Something "new" from jeti in the 2013 catalogue from their site: Looks like the central box 200 is coming soon here are some technical data (google translation sorry) Central Box CB200 The CentralBox 200 represents a combination of a high power accumulator separating filter without voltage reduction, 15 programmable and safe servo connect...

Tail Servo HOT. WTH?!

helifreak.com - 2013-03-18 02:29:18 - Similar - Report/Block

Hey Everyone, Setting up my 300X that I got used. I'm using an Align 3GX and have the stock servo setup as digital, 1520 frame rate. Thought at first I had some binding (though it looked okay) so I popped off the servo arm. The servo got really HOT and I think it got damaged. Took the servo off from my other spare airframe and the same th...

JPA Entity relationship: Cascade on delete

stackoverflow.com - 2012-06-06 13:55:37 - Similar - Report/Block

I am using spring, JPA with Hibernate. I got the following entities: @Entity @Table(name = "Supplier") public class Supplier { @Id @Column(name = "Supplier_ID", nullable = false) private Integer supplierId; ... @Entity @Table(name = "Product") public class Product { @Id private Integer productId; @ManyToOne(cascade = CascadeType.AL...

8FG battery voltage

helifreak.com - 2013-06-11 13:07:12 - Similar - Report/Block

Hey guys recently converted from a Spektrum DX8 to the Futaba 8FG Super, boy am I glad I did. As I have only been in the hobby for about 8 months I have only had experience with lipos (ran a lipo in my DX8 too). So my question is how low should I run the 8FG nimh TX battery? At what voltage will the 8FG shut off / warn me of low voltage?...

New Goblin 770 for Sale (Never Flown)

helifreak.com - 2013-06-12 03:18:37 - Similar - Report/Block

I am offering for sale a beautiful, meticulously assembled Goblin 770. I purchased this together with a Goblin 700 about a month ago. I抦 keeping the 700 for my own use, but I抦 going to sell this 770. This heli has never been flown and the AR7200BX will require setup. I抳e included a list of parts below. Here is what is included in this pac...

High Voltage Vaping

e-cigarette-forum.com - 2012-09-09 16:41:31 - Similar - Report/Block

I'm using a Lavatube with a high resist tank, I always set the voltage 5.7-6.0 Im getting a dual 18650 box mod that the voltage will go up to 7.4-almost 8 on a full Charge. has anyone Vaped at these high voltage levels. Do you have any tips or advice? I Vape an all LIquid(which I am considering thinning out a bit). Any help would awesome...

Gun Manufacturer Sturm Ruger Won't Be Leaving Connecticut

opposingviews.com - 2013-05-01 16:38:04 - Similar - Report/Block

Michael Fifer, the president and chief executive of Sturm Ruger, recently told stockholders that the company would not leave Connecticut. Connecticut has had a rocky relationship with gun manufacturers lately. Following the Sandy Hook massacre Connecticut passed some of the strictest gun control laws in the nation – so strict, in fact, th...

MKS-BLS980 High Speed BLS Rudder Servo

helifreak.com - 2013-02-28 14:33:53 - Similar - Report/Block

In excellent condition. Please note that in order for this servo to work, the correct frequency of 760 must be selected. $80 shipped anywhere in the USA Dimensions: 40 x 20 x 40 mm ( 1.57x0.79x1.50 in) Operating Voltage: 4.8 ~ 6.0 V DC Volts Working frequence: 760μs / 560hz Bearing Type: 2BB Motor Type: Brushless Motor Attached Thumbnails...

2x7950 + 6570 =cant change voltage in Afterburner

guru3d.com - 2013-03-18 13:12:05 - Similar - Report/Block

Hello! I used 2x7950 and Afterburner let me control voltage without problem. But after I plugged in another 6450, then replaced it with 6570 and connected my monitor to it, Afterburner wouldn't let me change voltage, (any changes in the configuration of AB does not change anything) I can only change core and mem frequency of these 3 cards...

Who Has The KST 215MGs At 7.4 Volts?

helifreak.com - 2013-05-21 18:21:47 - Similar - Report/Block

Been reading and researching quite a bit lately about these servos and I realize there have been other threads about them. I want to know who has been running them at 7.4 Volts... and how they hold up and perform. The 3GX can handle up to 8.5 Volts. In my experience, the more power it can get- the better and more reliably it performs. The...

No tail servo??

helifreak.com - 2013-04-12 03:22:30 - Similar - Report/Block

Hooking up my new g31 just opend it and going through the set up and I have no tail servo. It's align ds520 and I have it set to 1.5ms@333Hz. I have no power to the servo and the servo and the unit is brand new. I ha e moved the servo to a different Rx and it works fine? Any help would be appreciated. I have tried to call Robird USA and c...

cell voltage meter for JST-PH

helifreak.com - 2013-04-30 21:34:47 - Similar - Report/Block

So I have the Blade 130x and Turnigy Accucel charger. I would need a good way to check battery voltage in the field when I don't have my charger with me. Can't find a voltage check meter on Hobbyking that would fit the JST-PH (UMX style) connector. What cell checker should I buy? How do you check the remaining voltage or mAh? My charger s...

7870 XT undervolt problems

hardforum.com - 2013-04-19 11:40:10 - Similar - Report/Block

Im having issues trying to undervolt this card with sapphire trixx and msi afterburner (the latest beta) What i am trying to accomplish is the following: in idle mode i want the card to clock the lowest and drop the voltage with it (at default it drops to 300mhz core, 150mhz ram @ 0,8V) and that is what it does. When i jump into a game, t...

KST 515MG Servos

helifreak.com - 2013-02-08 05:08:10 - Similar - Report/Block

Has anybody seen this servo or have experience with KST? I think KST is a rebrand of RJX / Servoking servos? Not really sure. The specs look really nice, but it's pretty much unknown at this point and I can't find anybody using the servo as a cyclic on a 500. I'm getting ready to replace the TGY cyclical and contemplating the risk here. I...

AR7200BX Problem HELP

helifreak.com - 2013-02-20 13:49:37 - Similar - Report/Block

i just hooked up a brand new unit on a Trex 500 and when i plug the cyclic servo in the Aileron Servo go crazy Buzzing and moving Tweeking if i move the servo to Elevator or the pitch imput the servo is fine. i have 2 AR7200Bx on 450 size heli with no Problem just looking for Help The Servos are Hitec 5245 MG servo...

Z87 Extreme 6: How to configure adaptive voltage options?

tweaktown.com - 2013-06-10 11:18:50 - Similar - Report/Block

Hiya, So far I've succesfully overclocked my Z87 Extreme 6 with i7-4770K to 4.6GHz on 1.275V ... (tried 4.7GHz as well, but I did not yet want to push the voltage over 1.3V to get it stable - Handbrake crashed after a few minutes). At 4.6GHz and with AIDA64 stability testing, the temperatures reach the mid to high 80's on air (as expecte...

Hdmi gear sound high quality has considerable distinction

informationbible.com - 2013-03-20 14:00:00 - Similar - Report/Block

speaker cable china,speaker cable company,speaker cable wholesale,speaker cable manufacturers, speaker cable manufacturer,speaker cable suppliers,speaker cable supplier, transparent speaker cable,red and black speaker cable,...

Vari-tube too hot issue (Voltage coube be wrong)

e-cigarette-forum.com - 2013-03-15 09:13:14 - Similar - Report/Block

Got a Vari-tube (young june) and the vapor is very hot even when voltage is set to 3.0V. Does anyone got the same problem? The current measured at the end cap is about 2.25-2.35A. Battery is fresh at 4.15V. I can't measure the actual voltage on the wire, but by calculating from the current/wattage it uses, the voltage on the clearomizer i...

microheli 130x rotary frame and hitec 5035 servo questions

helifreak.com - 2013-05-29 03:01:59 - Similar - Report/Block

Ok how are they getting away with the voltage output on the 3+1 board to the hitec servos. The hitecs are a 4.8 volt servo and the 3+1 only outputs what 3.8 volts ??? Yes I like my custom 130x so much(recent build) that I am considering another with rotary servos. Just wish lynx had their rotary frame ready but the microheli will have to...

Is my lipo ok? Voltage vs mah left?

helifreak.com - 2012-08-04 19:38:26 - Similar - Report/Block

Did a 6 min flight and came down with 3.82 on my 6s 5000 on my trex 550. When I went to put a charge on the pack it only took about 2900 mah. Now that's not down to 20 %. Why is my voltage down but my remaining capacity on the high side? Could I have flown for another min or so? What should I be more mindful of the voltage or capacity? Th...

What voltage do I choose to power my charger?

helifreak.com - 2013-05-03 04:17:22 - Similar - Report/Block

Hey guys, I'm having a hard time finding an answer. I have a TeamGreatHobbies 1000w charger and just received my 1200w efuel power supply. The power supply has adjustable output voltage of 15-24v, the charger can accept 11-32 volts. But what do you set the output voltage for of the PS? I'm charging 6S batteries 95% of the time, so would 2...

Sale SAB GOBLIN 500 RED and Electronic BRAND NEW & UNFINISHED

helifreak.com - 2013-05-01 14:01:00 - Similar - Report/Block

Hi, I got the BRAND NEW UNFINISHED SAB GOBLIN 500 RED and Electronic FOR SALE. I DID about 5-10% Build, on metal frame between cyclic and main-shaft, The rest it sealed and new. I brought some of the electronic that recommended BRAND NEW, I can't continue... can't afford Goblin right now and the part are above my head. I really Like Gobli...

Elevator servo failure

helifreak.com - 2013-06-05 07:41:04 - Similar - Report/Block

having 2 elevator servos fail on my 450x and reading serveral other posts on the same I got to thinking maybe because the lipo sits right on the servo the heat from lipo may be adding to servo failure... I made a small plastic piece and glued it just above the servo on the frame of heli in front of the motor to keep the lipo off the servo...

Ego vv or ego v6

e-cigarette-forum.com - 2013-03-23 18:23:28 - Similar - Report/Block

Hi, I have a Variable Voltage Ego Cig, the one with the LCD display and it has voltage between 3v-6v. I am vaping this with a rebuildable CE4 clearomizer. I want to know whether to switch to Ego V6 - this is the one with 3 voltage settings which are: 4v, 5v and 6v and it has Takes two 16340 batteries. Which ones gives better vapour etc? A...

JR 8900G Tail Servo

helifreak.com - 2012-08-31 05:12:21 - Similar - Report/Block

Just sold my 700e Airframe, now im parting the rest out. JS 8900G Tail Servo No crashes on servo and has a new gearset installed about 15 flights ago. Since servo was on my 700e, the servo lead is long enough to reach the front radio tray (extended it). Asking $80.00 Shipped Paypal Only Please...

Servo? Governor? Rx?

helifreak.com - 2013-05-05 05:18:04 - Similar - Report/Block

I went to the field Thursday and had problems with my 700n. I spooled up and when it would get light on the skids the throttle servo would go back to an idle position. It did this several times before finally lifting off. I thought the engine was bogging down until I could see the servo horn going back to the idle position. I shut it down...

Which tail servo arm?

helifreak.com - 2013-03-21 17:22:22 - Similar - Report/Block

I broke my tail servo arm, and need to get a replacement. I am struggling to find which arm is the correct one for the 500 dfc. I have read I need a distance of 11 to 12mm for the ball link. But can't find any servo arms which are that short (and also located in the US, hate to wait a month for a servo arm). I also will need the ball link...




dialogShowMessage!

Fill out the form you see below. Registration is free, fast and simple.
If you are already registered, sign in page login.


Web Site :
Required Field
First Name :
Required Field
Last Name :
Required Field
Email :
Required Field
Sex :
Required Field

evolveStar.com is free for ever !


evolveStar.com provides a search engine that allows you to gather information to write their own blog.


evolveStar.com enhances the sources displaying the logo of the site.


If you want to remove your site or you believe a site listed infringes copyright, please report it to: info@evolvestar.com


Specifies the subject copyright violation and the url of the page


evolveStar.com respecting the law DMCA (Digital Millennium Copyright Act) will immediately remove whatever its merits.


Next will be effectual and relevant checks.







Who We Are Partner Advertising Contacts Privacy terms Help & FAQ

© Copyright 2010-2017 Fabrizio Fichera. All rights reserved.