1999 Acura CL F23A1 timing belt

honda-tech.com - 2013-04-22 16:02:41 - Similar - Report/Block

First off -I'm an old diy'er currently driving a 1964 Corvette and 1931 Ford 5 window coupe street rod. Although the wife and I do also have a 2004 S2000 with only 22K miles on it - nice car, all black. So, 3 cars and 6 seats total. Looking at a 1999 Acura CL to buy. Have no clue about this new fangled technology. I've read the excellent...

Are the factory timing belt made in Korea or USA?

hyundai-forums.com - 2013-03-05 06:12:41 - Similar - Report/Block

Hi, I just bought an 05 Hyundai Elantra with 80k miles on it and I'm trying to figure out if the timing belt has been changed yet. The belt looks fine but there is no way to tell how old it is. However, I did notice the belt said "made in usa" next to the barcode and white lettering on the belt. Could anyone who hasn't gotten a new timing...

Oil leak, residues on timing belt cover

iwsti.com - 2012-09-14 05:14:15 - Similar - Report/Block

So i had my timing belt, power steering pump, and idler pulley replaced a few months ago at a Subaru dealership. On my last two oil change, i noticed a little residues of oil near the oil filter and on the timing belt cover, but i figures it was normal so didn't really worry about it. But recently i've noticed my oil consumption was more...

1998 accord V6 timing belt job

honda-tech.com - 2013-03-20 04:02:15 - Similar - Report/Block

Going to change the timing belt on an accord I just bought. It has 130,000 miles and I'm not sure if it has ever been done. I have a couple questions: 1.Is there a write up out there anywhere? I have looked and looked and cant find one. 2.What all should I replace? I planned on the timing belt and water pump, anything else I should replac...

Timing belt kit question

yotatech.com - 2013-02-28 03:45:54 - Similar - Report/Block

Ok I'm picking up a used motor has 78k on it. What all should I do for the timing belt stuff. I know timing belt and water pump what else should be done thanks also oem or name a good aftermarket brand. Wanna be good for the next 100 k...

timing belt and major tune up

toyotanation.com - 2013-05-10 05:24:12 - Similar - Report/Block

hi guys, im doing a timing belt change along with a major tune-up, but i cant seem to get the toyota part numbers right. i have a 96 camry LE 5S-FE. this is what i have so far: 13568-09041 Timing Belt 16100-79185-83 Water Pump w/gaskets 90507-17003 Tensioner Spring 15188-63010 Oil Pump o-ring 15165-70010 Oil Pump Drive Seal 90080-31023 Ca...

d16y7 timing belt done wrong?

honda-tech.com - 2013-03-18 06:12:05 - Similar - Report/Block

i just swapped a new motor into my 1996 civic cx motor was out of a 1999 civic dx, i was having trouble starting the motor so i turned the alternator counter clockwise and got the engine running, and idleing no problem, when i rev the motor up it revs up fine but when i let go of the peddle for the engine to go back to idle it makes a wei...

99 toyota solara timing belt keep slipping

toyotanation.com - 2013-03-27 04:08:21 - Similar - Report/Block

I just did the timing belt on my 99 solara....all set..all marks are right on fire up the car it fires right up. Rev the car heard slipping sound. Then the engine shakes and misfire. I manually crank it off again. I did it again for the third time, i make sure no slacks, even help the tensioner put more tension on the belt just lifting it...

Wrong distributer effecting ignition timing?

honda-tech.com - 2013-03-21 09:24:50 - Similar - Report/Block

I recently replaced the timing belt on my civic and cant achieve corrrect ignition timing. Before changing the belt the car failed smog due to extremely high lvls of nox (all other emissions wer well within spec and co2 was almost 15%) The ignition timing was off (8 btdc) but the distributer was fully advanced. So after checking cam timin...

Rough idle after Timing Belt Change

honda-tech.com - 2013-05-08 18:27:45 - Similar - Report/Block

So a mechanic i know did a timing belt job for me(Water pump and all that with a whole kit.) I picked up the car drove it home, noticed in the morning when i turned it on and let it warm up that at idle i could definitely tell it was louder, and the car itself was shaky. If i put my hands on the steering wheel i can feel the vibration a l...

CT RB26 valve cover set for your RB20 set*

zilvia.net - 2013-03-15 06:34:12 - Similar - Report/Block

Hey guys, I have a set of RB26 valve covers and a timing belt cover. I'm looking to trade for a RB20 set with a coil pack cover as well plus cash on your end. These parts are primed and ready to be put onto your motor. The only modification you have to make is to trim the guard that is behind the timing belt cover a little bit to fit on e...

Timing Belt Advice and Concern

yotatech.com - 2013-05-08 13:52:50 - Similar - Report/Block

Hey all, So my 1989 Toyota 4Runner SR5 with the V6 engine has 310,000 miles, and I have no idea when the timing belt was last serviced. The truck has been meticulously maintained mechanically, so I am hoping it is okay, but nevertheless I need to have it checked. Firstly: What is the consensus on part manufacturer? I am tempted to stick w...

evolveStar Join

2004 Sonata Timing Belt Replacement/Maintenance

hyundai-forums.com - 2013-06-04 08:33:51 - Similar - Report/Block

On a recent visit to my local Hyundai dealer with my 2004 Sonata 2.4L it was suggested that the timing belt (among other things) be replaced. The issue is that although the car is 9 years old it only has 35,000 miles and has been lightly used. But the dealer says that because of the heat (I live in Louisiana) and the age of the car, the t...

Side timing marks won't fully line up. B18C1

honda-tech.com - 2013-03-17 15:29:40 - Similar - Report/Block

Installed my new timing belt but the marks on the side of the cam gears don't fully line up. I spent a good 2 hours trying to align them the crank is set at TDC there is enough slack on the belt and the car starts and runs fine. Vtec hits also the head was milled at some point but i don't think it was enough to affect the timing. The pic...

High Idle and chugging at 2000-3000 rpms...help!

yotatech.com - 2013-02-28 04:48:54 - Similar - Report/Block

Experiencing some similar problems with my 1999 4runner 3.4 but also some other interesting ones. Background: My 4runner had a CEL on for a while, and one day i was driving it, the engine starting making a loud ticking sound, and needless to say, i should have stopped driving there instead of attempting to get it home. Ended up blowing up...

96 Camry LE 2.2L major tune-up

toyotanation.com - 2013-05-01 09:18:20 - Similar - Report/Block

Hey guys, this is my first post on TN, just register. I want to say, the DIY's on this site are gold. I got a 96 camry 2.2L last year with 110K on it, drove it to 145K so far, along with a cross country drive. Car is in great shape, but I want to do some major tune-up on it to keep it running long term. I have a leak from the timing belt...

Loud screeching noise coming from passerner side. timing/other belt ?

honda-tech.com - 2013-03-01 09:16:40 - Similar - Report/Block

I've got a 94 GSR and today I noticed that there was a horrid screeching niose. coming from the passernger side when the cars rpms are between 1-2.3k stationary or moving. my 99dx did this when i only had one bolt holding the ps pump. but that's what makes me think it's a belt of some sort alternator or timing belt ?. it stops when the ca...

What if, timing belt brakes

hyundai-forums.com - 2013-03-27 09:24:37 - Similar - Report/Block

Many car engines can handle a broken timing belt without anything serious happening other than the motor stops. What about the Hyundai (Mitsubishi Sigma?) V6 engines? Will the valves or the pistons be damages?...

TX fs: HKS RB25 timing belt

zilvia.net - 2013-03-21 07:44:45 - Similar - Report/Block

Like title says, rb25 hks timing belt for sale. Brand new are about 160-170. Selling mine for 140 obo Only used it for about 6 months on my drift car which is not daily driven, and I only took my car to about 3 drift events with it. Reach me at 832 704 5233 Yes I will ship...

Stumped on some timing belt issues

yotatech.com - 2013-05-29 07:03:30 - Similar - Report/Block

Hey guys, I'm new here and I've been searching for a problem like mine but haven't found anything so hopefully one of you can help me out. I have a 1990 4runner v6. I keep having the timing belt slip. The first time I assumed it was just worn out parts so I replaced the belt, idler pully and tensioner (aftermarket autozone parts) back in...

Quantum 4120-1200 Getting really hot...

helifreak.com - 2013-03-04 01:53:37 - Similar - Report/Block

Im having heat issues. How tight is your belts? Did you use only spring tension on the motor belt? I pulled on the motor as i tightened it, same with the tail belt. And I have timing at 5 and 12hz. After a hard 4 min flight its almost to hot to touch. I cant hold it more than a few seconds... I heard these run cooler than scorpion so I we...

2005 se v6 engine stumble.. HELP!!!

toyotanation.com - 2013-02-15 06:36:30 - Similar - Report/Block

just bought an 05' SE V6, with the 3.3 engine. seemed to run good, had it checked by shop and they said it was agood buy, so i bought it. first day i owned it, took it to toyota dealership in vegas and had them do a 90, 000 mi service. did a timing belt, watr pump, tranny flush, oil change. got the car back, and it ran like crap! it would...

Timing Belt Replacement

honda-tech.com - 2013-05-01 17:26:24 - Similar - Report/Block

I've owned Accords for 21 years, and with each one I've replaced the timing belt when scheduled and that has usually happened within 5 years. I currently own a 2006 V6 with 79K on it, and the dealer is saying that the replacement guideline is 7 years or 105K miles. The manual makes no mention of "7 years or", and the folks at Honda in CA...

96 Misfires, low rough idle after timing belt & tune up

toyotanation.com - 2013-02-26 01:00:12 - Similar - Report/Block

I got ambitious, did the following and am now stuck... Background... 1996 4 cylinder Camry LE 221K Prior to work car ran really well except timing belt was slapping the case and covered with oil. Also had a CEL P0401 code and some oil leaks. Work Performed... Replaced timing belt, pulleys, tensioner spring, cam/crank seals, oil pump rotor...

Domains registered since the 90's: MVPGaming(.)com, LayawayOnline(.)com ++

dnforum.com - 2013-06-06 17:43:00 - Similar - Report/Block

All the following domains registered since the 90's are for sale: Domain - Price - Age AllAboutBiz.com - $2,000 - 1997 AutomatedCashFlow.com - $800 - 1999 CentreFund.com - $600 - 1996 Create-Wealth.net - $200 - 1999 FanLists.com - $800 - 1999 HowLowCanWeGo.com - $250 - 1999 HuntingDaily.com - $800 - 1999 LayawayOnline.com - $500 - 1999 Li...

When to change Timing Belt...Yaris 2008

toyotanation.com - 2013-02-20 08:13:49 - Similar - Report/Block

Hi - I own a 2008 Yaris with 69,500 miles on it. The timing belt hasn't been changed, but I was wondering when it should be replaced? I'm taking my car in for an oil change, should I just ask them how it looks and rely on them to tell me when to change it?...

Painting timing belt cover?

honda-tech.com - 2013-06-10 08:40:55 - Similar - Report/Block

Im in a process in rebuilding my enigne d16z6 motor. painted the block etc.. the question is that what can i use to paint the timing belt cover i have cleaned it good removed dirt and looks clean, but i want to make it look colored. i have have extra high temp engine dupilcolor primer, duplicolor engine enamel, and high temp. clear coat.

FS: Freshly powder coated top end kit j32/j35

acurazine.com - 2013-03-05 06:54:30 - Similar - Report/Block

Top end (upper intake valve covers) kit for j32 and j35 first gen motors. First gen j-series motors are used in the following vehicles: HONDA 1998-2002 (j30a1) Honda Accord 3.0 1999-2001 (j35a1) Honda Odyssey 3.5 2002-2004 (j35a4) Honda Odyssey 3.5 2003-2004 (j35a4) Honda Pilot 3.5 ACURA 1998-2003 (j32a1/j32a2) Acura TL 3.2 (base and Type...

89 ef obd1 converted b18a1 ~trouble starting~

honda-tech.com - 2013-04-25 02:41:41 - Similar - Report/Block

When we first swapped it we started it and the water pump was leaking the only codes we were getting at that time was 41 ( o2 sensor ) which we havent wired up yet. Then we changed the water pump and timing belt and the car started up fine again drove it around but it felt like it was a tooth off no low end power. Took off the timing belt...

Help for 92' Honda Prelude Cylinder Head Rebuild

honda-tech.com - 2013-04-21 18:14:31 - Similar - Report/Block

I have a 92' Honda Prelude that had a timing belt break and consequently it bent two exhaust valves. I replaced the timing belt, the balancer and tensioners, machined the head and got new valves and guides and finished rebuilding it but now it won't start. The engine is unique with a 2.2 block and its always had the 2.3 dual overhead cam...

Help Me Get My RB26 Running

zilvia.net - 2013-06-04 15:50:45 - Similar - Report/Block

Hey guys, so ive been working on building an rb26 s13 for alittle over a year now. I got it to start but its running pretty rough. When I first start it, it runs pretty smooth, but the hotter it gets the more eratic the idle gets. It starts haunting and jumping from 1500-2500. Heres a list of things done to the motor. I did a full rebuild...

3.0 water pump/ timing belt kits ?

yotatech.com - 2013-04-22 03:09:57 - Similar - Report/Block

95 SR5 3.0 needs a water pump so, with 60k since timing belt was replaced I might as well do everything on the front end ? What are your thoughts on kit's like these and also, I have a fair amount of wobble in the fan clutch(bearing?) which may be why water pump failed. Truck has 230k and will not be a daily driver just for hauling and to...

Pleaes help me start my car =0/

honda-tech.com - 2013-03-11 17:01:57 - Similar - Report/Block

So here’s everything I did and why… 1998 accord 2.3vtec I took the timing belt off because this car had a bad head gasket. Some guy had replaced the head for my mother in law due to the gasket blowing before but didn’t flush the coolant so the oil+coolant goop was clogging the system. It started overheating again so another guy tore it do...

Brittany O.'s Review of Acura of Lynnwood - Lynnwood (5/5) on Yelp

yelp.com - 2012-04-10 23:59:03 - Similar - Report/Block

I bought my first Acura from Acura of Lynnwood and recieved wonderful customer service the entire time. I went to Acura of Lynnwood for every oil change and for every maintenance issue bc i trust…...

FS: 2013 Navigation Disc Orange V3.C0

acurazine.com - 2013-04-16 23:35:12 - Similar - Report/Block

Hi AcuraZiners, For Sale: 2013 Navigation Disc Orange V3.C0 Price: $95 shipped I just traded in my 04' Acura TL. So here I am. Selling a used Nav disc (in perfect condition). I bought this New from Acura at the beginning of the year for $162.22. It is compatible for Acura RL 2004 Acura TL 2004 - 2006 Acura MDX 2003 - 2004 Acura TSX 2004 -...

'The 2005 Acura RL Is Luxury's New Turn'

jalopnik.com - 2013-05-08 23:10:27 - Similar - Report/Block

When other companies zig, Acura zags. For example, the Cadillac Catera zigged. So, in reaction, the Acura TL zagged. Get it? Good. Read more...

Slight Misfire?

toyotanation.com - 2013-04-11 09:44:52 - Similar - Report/Block

My car has had a slight misfire since i got it. Sometimes, rarely, and usually when its colder, it can run REALLY rough. Like undriveable for a few minutes. I changed the spark plugs, and timing belt, and the timing is good. My guess is it needs new plug wires, and maybe a new distributor/ cap. Any input? I can get a video in a few days i...


honda-tech.com - 2013-05-05 07:53:23 - Similar - Report/Block

My timing belt snapped and went into my cam gears and jumped the motor basically cylinder head is @&@$ on my 1992 Acura Integra GSR. So the beast has been SLEEPING for 5yrs going on 6 this yr... It's GOTTA WAKE UP this YR now I'm thinking bout getting a Type R head or just do a whole Type R SWAP or just port polish the cylinder head and r...

Worth to reman the head while doing timing belt?

toyotanation.com - 2013-03-21 18:49:17 - Similar - Report/Block

I've been reading this forum for a few days and noticed most 2.7L engine has blown head gasket issues at higher mileage. My 95 v6 is at 211k and still running strong. knock on wood. My brother is about to replace the timing belt and water pump for me, along with all the other belts. He asked if I want him to remove the head and take it to...

91 Camry - Setting the Timing?...

toyotanation.com - 2013-03-21 02:04:55 - Similar - Report/Block

:help: So I've been reading this forum now for the last 2 weeks solid pretty much.. and everyone's posts have been EXTREMELY helpful ... as these posts have gotten me halfway through a timing belt R&R. So its taken me like 3 days solid now.. to get to the point of putting the belt back on... (Hint: i'm a computer guy, not a mechanic lol)...


Fill out the form you see below. Registration is free, fast and simple.
If you are already registered, sign in page login.

Web Site :
Required Field
First Name :
Required Field
Last Name :
Required Field
Email :
Required Field
Sex :
Required Field

evolveStar.com is free for ever !

evolveStar.com provides a search engine that allows you to gather information to write their own blog.

evolveStar.com enhances the sources displaying the logo of the site.

If you want to remove your site or you believe a site listed infringes copyright, please report it to: info@evolvestar.com

Specifies the subject copyright violation and the url of the page

evolveStar.com respecting the law DMCA (Digital Millennium Copyright Act) will immediately remove whatever its merits.

Next will be effectual and relevant checks.

Who We Are Partner Advertising Contacts Privacy terms Help & FAQ

© Copyright 2010-2015 Fabrizio Fichera. All rights reserved.